Hyundai Tucson manuels

Hyundai Santa Cruz 2021-2022 Owners Manual: Lighting

Exterior Lights

Lighting control

To operate the lights, turn the knob at the end of the control lever to one of the following positions:

1. OFF position
2. AUTO headlamp position
3. Position lamp position
4. Headlamp position

Daytime Running Light (DRL)

The Daytime Running Lights (DRL) can make it easier for others to see the front of your vehicle during the day, especially after dawn and before sunset. The Daytime Running Lights (DRL) should be illuminated whenever you are driving during daylight hours. The DRL system will be ON when the headlamp stalk is in the OFF or the AUTO Position (when daylight is detected) and the Electronic Parking Brake (EPB) is released.

The DRL system will turn off when:

AUTO headlamp position

The position lamp and headlamp will be turned ON or OFF automatically depending on the amount of daylight as measured by the ambient light sensor (1) at the upper end of the dash board.

Even with the AUTO headlamp feature in operation, it is recommended to manually turn ON the headlamps when driving at night or in a fog, driving in the rain, or when you enter dark areas, such as tunnels and parking facilities.


Position lamp position ()

The position lamp, license plate lamp and instrument panel lamp are turned ON.

Headlamp position ()

The headlamp, position lamp, license plate lamp and instrument panel lamp are turned ON.


The ignition switch must be in the ON position to turn on the headlamp.

High beam operation

To turn on the high beam headlamp, push the lever away from you. The lever will return to its original position.

The high beam indicator will light when the headlamp high beams are switched on.

To turn off the high beam headlamp, pull the lever towards you. The low beams will turn on.


Do not use high beam when there are other vehicles approaching you. Using high beam could obstruct the other driver’s vision.

To flash the high beam headlamp, pull the lever towards you, then release the lever. The high beams will remain ON as long as you hold the lever towards you.

Turn signals and lane change signals

To signal a turn, push down on the lever for a left turn or up for a right turn in position (A).

If an indicator stays on and does not flash or if it flashes abnormally, one of the turn signal bulbs may be burned out and will require replacement.

One touch turn signal

To use One Touch Turn Signal push the turn signal lever up or down to position (B) and then release it.

The lane change signals will blink 3, 5 or 7 times.

Battery saver function

The purpose of this feature is to prevent the battery from being discharged. The system automatically turns off the position lamp when the driver turns the vehicle off and opens the driver-side door.

With this feature, the position lamps will turn off automatically if the driver parks on the side of road at night.

However, the position lamps stay ON even when the driver-side door is opened if the headlamp switch is turned to the position lamp or AUTO (if equipped) position after the engine is turned off.

If necessary, to keep the lamps on turn the position lamps OFF and ON again using the headlamp switch on the steering column after the engine is turned off.

Headlamp delay function

If you place the ignition switch to the ACC position or the OFF position with the headlamps ON, the headlamps (and/ or position lamps) remain on for about 5 minutes. However, if the driver’s door is opened and closed, the headlamps are turned off after 15 seconds. Also, with the vehicle off if the driver’s door is opened and closed, the headlamps (and/ or position lamps) are turned off after 15 seconds.

The headlamps (and/or position lamps) can be turned off by pressing the lock button on the remote key or smart key twice or turning the headlamp switch to the OFF or AUTO position.


If the driver exits the vehicle through another door besides the driver door, the battery saver function does not operate and the headlamp delay function does not turn OFF automatically.

This may cause the battery to discharge. To avoid battery discharge, turn OFF the headlamps manually from the headlamp switch before exiting the vehicle.

Closing the fuel filler door
1. To install the fuel tank cap, turn it clockwise until it “clicks” one time. 2. Close the fuel filler door until it is latched securely. Information To lock the fuel filler door, make sure the ...

High Beam Assist (HBA)
High Beam Assist will automatically switch between high beam and low beam depending on the detected brightness from the lamps of oncoming vehicles or vehicles in front. Detecting sensor [1] : Fr ...

Autres materiaux:

Procédures de réparation
REMPLACEMENT 1. Retirez le bouchon et les écrous, puis retirez le bras de l'essuie-glace (A). Couple de serrage: 22,6 ~ 26,5 N.m (2,3 ~ 2,7 kgf.m, 16,6 ~ 19,5 lb-ft) 2. ...

Témoin du système antidémarrage (avec clé intelligente) (le cas échéant)
Ce témoin s'allume pendant 30 secondes dans les cas suivants : • Lorsque le bouton de démarrage/d'arrêt du moteur est en position ON et que la clé intelligente est détectée dans le véhicule. - Vous pouvez alors démarrer le moteur. - Le témoin s'éteint après le démarr ...

© 2016-2022 Kopyright